United States
Hong KongDishmachine Requirements
A high-temperature machine must reach 71°C (160°F) measured at the utensil surface, which is not what the front gauge shows - an irreversible temperature indicator is used to verify it.
- A chemical machine dispenses sanitizer at the label concentration.
On this page6 sections
Two kinds of machine, two different things to verify, and one number that catches almost everyone.
High-temperature machines
These sanitize with heat. The requirement is 71°C (160°F) at the utensil surface.
Do not confuse the wash tank with the final rinse
The 2026 FDA Food Code gives machine-specific wash-solution minimums and separate final-rinse temperatures. For spray machines using hot water to sanitize, the wash temperature depends on whether the machine is a stationary rack or conveyor and on its temperature configuration. Chemical-sanitizing spray machines have a separate wash minimum. The clean rule for an exam is to identify the reading being tested before using a number.
| Reading in the 2026 Food Code | Hot-water machine | Chemical-sanitizing machine |
|---|---|---|
| Wash solution, stationary rack, single-temperature spray machine | 74°C (165°F) minimum | 49°C (120°F) minimum |
| Wash solution, stationary rack, dual-temperature spray machine | 66°C (150°F) minimum | 49°C (120°F) minimum |
| Wash solution, single-tank conveyor, dual-temperature spray machine | 71°C (160°F) minimum | 49°C (120°F) minimum |
| Wash solution, multi-tank conveyor, multi-temperature spray machine | 66°C (150°F) minimum | 49°C (120°F) minimum |
| Final hot-water sanitizing rinse at the manifold | At least 74°C (165°F) for stationary rack, single-temperature; at least 82°C (180°F) for other machines; no more than 90°C (194°F), subject to the Code exception | Use the sanitizer and machine requirements that apply to the chemical process |
| Verification at the utensil surface | At least 71°C (160°F) using an irreversible registering device | Use a test kit appropriate to the chemical and verify its required concentration |
Those are not interchangeable readings. The machine gauge may report tank or rinse-water temperature; the utensil-surface check asks whether heat reached the ware. Follow the machine data plate and the locally adopted code, because FDA publishes a model code and jurisdictions adopt or amend it.
That is not the gauge reading. The gauge shows the water leaving the manifold, and heat is lost between there and the plate. Verification uses an irreversible temperature indicator - a strip or a thermolabel run through with a load, which changes color permanently if the surface got hot enough.
A scenario giving you a front-panel reading and asking whether sanitizing was achieved is testing exactly this. The gauge is necessary and it is not sufficient, and an answer treating it as proof is wrong.
Machines like this need drying time built in, because plates come out hot and air dry quickly. Stacking them wet defeats the whole cycle.
Chemical machines
These sanitize with a chemical dispensed into the final rinse, at the concentration on the label. Verification is a test strip matched to the chemical.
Water temperature still matters - too cold and the detergent stops working, and some sanitizers have a minimum temperature of their own - but the sanitizing step is chemical rather than thermal.
What both machines need
- A data plate stating the operating requirements, and operation within them.
- Pressure and temperature gauges that are readable and accurate.
- Spray arms clear, and jets not blocked.
- Items racked so water reaches every surface - not stacked, not nested.
- Scraping and pre-rinsing before loading.
- Air drying afterwards.
Racking is the operational failure that generates most of the real-world problems. A machine cannot clean a surface the water does not reach, and no temperature fixes that.
Records
A log of temperature or concentration checks at the start of each shift, and after any repair. It is the difference between a machine that works and a machine somebody believes works.
When the machine fails
Stop using it, and move to the three-compartment sink. The sink is the fallback, which is one reason the Code expects a functioning one to exist even in kitchens with a machine.
Running the machine anyway and hoping the next load is hotter is the option the exam offers to see whether you will take it.
Common questions
What temperature does a high-temperature dishmachine need?
71°C (160°F) measured at the utensil surface. The front gauge shows water leaving the manifold, not the temperature reaching the plate, so an irreversible temperature indicator is used to verify it.
How do you check a chemical dishmachine?
With a test strip matched to the sanitizer being dispensed, confirming the concentration on the label is being achieved in the final rinse.
Why can items not be stacked in the rack?
Water cannot reach a surface another item is covering. No temperature or chemical concentration compensates for a surface the water never touched.
What do you do if the dishmachine fails?
Stop using it and switch to the three-compartment sink, which is why a functioning one is expected even in kitchens that normally use a machine. Continuing to run a failing machine is not an option.
Do dishes still need to air dry?
Yes. Towel drying reintroduces contamination regardless of how the items were sanitized. Machine-washed items usually air dry quickly because they come out hot.