NRSB RRS Mitigation: Mitigation Troubleshooting and System Performance
Troubleshooting starts by defining the failure: the fan may not run, the pressure field may be weak, or indoor radon may remain elevated despite normal operation.
- Check records and system components methodically before replacing equipment.
- The RRS exam emphasizes electrical versus fan faults, obstructions, leaks, pit adequacy, foundation coverage, diagnostics and verification.
On this page12 sections
- Define what “not working” means
- Check power and fan operation safely
- Look for blocked or flooded piping
- Inspect leaks and connection integrity
- Evaluate suction-pit adequacy and substrate
- Test whether the system reaches every foundation zone
- Interpret system indicators carefully
- Retest with a comparable method
- A stepwise troubleshooting workflow
- Worked case: fan runs, result stays high
- Document findings and communicate limits
- Study the troubleshooting section
A homeowner may say a radon system is not working because the fan is silent, a manometer looks different, an alarm appeared or a new test remains high. These are different symptoms. The April 2026 NRSB RRS guide lists troubleshooting underperforming and nonfunctioning systems and asks whether the issue is electrical or mechanical, whether pipe is obstructed, whether pressure is lost, whether the pit is adequate and whether the system reaches all foundation areas.
- Credential
- NRSB Radon Reduction (Mitigation) Specialist
- Topic
- Mitigation Troubleshooting and System Performance
- Design principle
- Diagnose, design, install, verify and document
- Source guide
- NRSB Certification Exams Study Guide, April 2026 v1.1
Define what “not working” means
Start by asking what changed and what evidence prompted the concern. Compare the current condition with commissioning notes, fan model, pressure-indicator baseline and post-mitigation results. A single meter observation without a baseline may be difficult to interpret. Check whether the building, HVAC or system was modified since installation.
Do not promise that a fan replacement will fix the problem before testing. A functioning fan can coexist with a disconnected pipe, weak pressure field or incomplete foundation coverage. Conversely, an alarming-looking indicator may reflect a changed system configuration rather than a total failure. Diagnose the symptom and verify the outcome.
Check power and fan operation safely
For a nonfunctioning system, distinguish a power supply problem from a fan failure. Check the approved indicator, breaker status and accessible connections only within your qualification and local code. Do not open electrical equipment or bypass protection unless authorized. If electrical work is required, involve a qualified electrician.
A motor may fail, lose power, become noisy or operate outside expected conditions. The manufacturer’s instructions identify normal status and service requirements. Record model and serial data and review warranty or maintenance history. A fan that hums is not necessarily moving air properly; operation must be evaluated with appropriate pressure or airflow evidence.
If the fan is located in a restricted or hazardous space, follow safe access procedures. Do not climb into an attic or crawlspace without assessing fall, electrical, heat or confined-space hazards. Safety remains the first troubleshooting step, even when radon performance is urgent.
Look for blocked or flooded piping
The exhaust pipe can be blocked by water, debris, an insect nest, damage or an altered fitting. A sagging run may collect condensate. Inspect accessible piping and compare the layout with the as-built record. A restriction changes system resistance and may move the fan away from its intended operating point.
Do not clear a blockage by creating a discharge into the building or damaging the pipe. Follow the design and applicable standard for water management and repairs. If a drain or bypass is installed, verify that it preserves the pressure boundary and safely handles condensate.
After clearing an obstruction, check the pressure indicator and any test points, then perform the required radon measurement. Restoring fan noise or suction at the inlet does not prove that occupied-air concentration is back within the intended range.
Inspect leaks and connection integrity
Loose, unglued or damaged pipe joints can leak soil gas or dilute the system’s suction. Look at visible connections, seals around the suction point and the fan housing. A leak may cause a pressure drop or allow exhaust to escape into an attic, garage or occupied room. The location and direction of the leak matter to both performance and safety.
Use the approved diagnostic method to locate a suspected leak. Smoke can show airflow direction qualitatively, while pressure measurements can help identify loss along the system. Keep diagnostic conditions consistent. Do not use a visual clue as the sole proof of quantitative performance.
Repair using materials and procedures appropriate to the pipe and standard. Document concealed work and retest. If the leak occurred in an exhaust section, explain the potential exposure concern and the timeframe, and refer the client to the relevant public-health guidance if needed.
Evaluate suction-pit adequacy and substrate
An undersized or poorly excavated suction pit can limit the collection area and create high resistance. The NRSB outline calls out checking whether the pit was excavated sufficiently and understanding substrate composition and porosity. Review original installation notes, diagnostic pressure measurements and any change in performance after repair.
A pit that worked in one area may not communicate through dense soil, wet fill or a barrier. More excavation is not automatically the answer; utility locations, slab integrity, drainage and structural safety must be considered. A new test point or suction location may reveal whether the problem is collection geometry or another system component.
If the design changes, repeat the relevant pressure-field tests and document the new configuration. Do not compare results taken under dramatically different conditions as if they were a controlled before-and-after test.
Test whether the system reaches every foundation zone
A home may contain multiple slabs, subgrade walls, additions, block walls or crawlspaces. One suction point might not influence every region. The NRSB guide explicitly asks whether the system reaches all parts of the foundation. Use test points, pressure measurements and building mapping to check the actual zones rather than relying on the fan’s nameplate.
A weak area may need another suction point, a separate system, a different foundation strategy or improved communication. The right correction depends on evidence and current standards. A stronger fan is only one possible response and may be ineffective if the zone is isolated by a footing or dense material.
Follow-up radon measurements should cover the areas and purpose specified by the applicable post-mitigation protocol. A satisfactory result in one basement room does not automatically establish that an attached crawlspace or separate slab is controlled.
Interpret system indicators carefully
A U-tube manometer or electronic indicator generally shows a pressure condition at a selected point. It can alert an owner that operation changed relative to commissioning, but it is not a direct radon sensor and may not represent every suction point. Explain what the indicator does and what it cannot prove.
If a reading changes, check whether the tube is intact, the reference points are open, the fan or piping changed, and the original baseline was recorded. Do not assume that a zero reading always means fan failure or that a familiar displacement guarantees a low indoor concentration. Use the manufacturer and standard’s interpretation.
An owner should know whom to call if an indicator changes or a fan stops. Include the normal baseline in the handoff and make follow-up measurement part of the long-term management plan where required.
Retest with a comparable method
A post-repair radon test should match the relevant standard, building use and decision. Keep location and duration comparable where the protocol requires it. Record weather or operation where relevant. If the system has just been altered, allow the prescribed stabilization or operating period before testing.
Compare the results carefully. A higher or lower value may reflect changed weather, HVAC, occupancy or measurement method as well as system performance. Do not cherry-pick the favorable result. Use the protocol’s rules and explain uncertainty. If performance remains unsatisfactory, continue the diagnostic cycle.
System checks and radon tests provide complementary evidence. A pressure reading can confirm system operation; a radon measurement assesses indoor outcome. Neither replaces the other. A good troubleshooting report ties each finding to a specific corrective action and follow-up.
A stepwise troubleshooting workflow
A disciplined sequence reduces wasted effort: review original design and baseline; interview the owner about changes; inspect power and fan; examine visible pipe for water, debris and damage; assess joints and suction connections; measure pressure at relevant points; test foundation coverage; then choose a correction and verify it. Record each step and the conditions under which it was performed.
If a simple issue is found, such as a tripped breaker, correct it within authorization and check the system. If the cause is unclear, expand diagnostics rather than swapping parts at random. If safety concerns appear, pause work and use the appropriate trade or authority.
This sequence is valuable in exam scenarios because distractors often jump to a repair. The best next step is usually a diagnostic action that separates possible causes. For example, a fan not running calls for power and motor checks; a running fan with poor reduction calls for field, leak, obstruction and coverage evaluation.
Worked case: fan runs, result stays high
Suppose the fan is running and the indicator looks normal, but post-mitigation testing remains elevated. Confirm the test’s validity and compare it with the original locations and methods. Inspect piping, exhaust discharge, accessible joints and suction connections. Then test whether pressure extends into each foundation zone.
If pressure is weak at remote points, investigate substrate, pit size, isolated slabs or barriers. If pressure is strong but radon remains high, consider bypass pathways, incomplete sealing, a different source or changed building operation. Gather evidence before deciding to enlarge the pit, add a point or change ventilation.
After a correction, commission the system and repeat the measurement. Tell the client exactly what evidence changed. A claim that the system is now “fixed” should rest on appropriate verification, not just a stronger fan sound.
Document findings and communicate limits
The service record should capture the complaint, system configuration, measurements, observed defects, diagnostic conditions, repair and follow-up plan. Use photos or sketches where concealed routes or multiple suction points matter. Record who performed electrical or plumbing work when another trade participated.
Explain the difference between restoring system operation and confirming radon reduction. If the fan failed, the owner should know the period of downtime if known and the recommended next measurement. Do not claim a health outcome from the outage period; refer individual health questions to a clinician or EPA.
If the system cannot be restored promptly, communicate practical steps within your scope and refer to local guidance. Never ask occupants to disconnect alarms or ignore electrical hazards to keep the fan running.
Study the troubleshooting section
Make a diagnostic tree with four branches: power/fan; airflow obstruction or water; leakage/connection; pressure-field coverage. Under each branch, list evidence that supports it and a safe next test. Add a fifth branch for an elevated result despite normal apparent operation, which forces you to distinguish outcome measurement from system indicator.
Review the current NRSB guide and ANSI/AARST mitigation standard for exact procedures and acceptance criteria. Product manuals are primary sources for fan operation; local code controls electrical work. Avoid memorizing one manufacturer’s fault codes as universal RRS knowledge.
Effective troubleshooting eliminates causes systematically rather than relying on equipment replacement. Even when an owner wants the fastest repair, a short diagnostic sequence can prevent repeat visits and unnecessary equipment changes.
NRSB’s April 2026 guide identifies the key troubleshooting causes, including electrical versus fan failure, obstruction, leakage, insufficient pit and incomplete foundation coverage. ANSI/AARST standards and manufacturer instructions govern exact diagnostic and repair steps. EPA materials provide general radon-reduction and health context.
This article is not a repair manual and does not provide wiring instructions, pressure acceptance values or fan-selection specifications. Use current standards and qualified trades. Each system should be evaluated in the context of its original design and current building conditions.
A complete troubleshooting job ends with documented evidence, a safe operating system and an appropriate follow-up radon measurement. The system’s apparent normality is a clue, not the final result.
Common questions
What should I check first when a radon fan stops?
Verify the observed symptom and check the approved power and status indicators within your qualifications. Follow manufacturer instructions and local code. Use a qualified electrician when electrical work is required; do not bypass protection.
If the fan runs, why might radon remain elevated?
Possible causes include weak pressure-field extension, a leak, blocked piping, an undersized suction pit, an uncovered foundation zone, changed building operation or an invalid follow-up test. Diagnose the evidence before replacing equipment.
Does a manometer prove that radon levels are low?
No. It shows a pressure condition at a measurement point. It can indicate a change from baseline, but post-mitigation radon measurement is needed to evaluate indoor concentration.
Should a stronger fan be installed when mitigation underperforms?
Only if diagnostics show the fan is mismatched to the system. A stronger fan will not necessarily fix poor communication, leaks, obstructions or isolated foundation areas.