NRSB RRS Mitigation: Active Soil Depressurization Design and Pressure Fields
Active soil depressurization (ASD) reduces radon entry by creating a pressure field that draws soil gas from beneath or beside the building and exhausts it outdoors.
- Effective design depends on the foundation, soil communication, suction-point location, airflow resistance and safe discharge.
- The RRS exam expects design reasoning; a fan name or pressure reading alone is not a complete system.
On this page11 sections
- The objective: control the soil-gas pressure relationship
- Sub-slab communication and pressure-field extension
- Choose suction locations from evidence
- Understand pressure and airflow together
- Negative-pressure sources and indoor safety
- Sealing and pressure field work together
- Plan a design for complex foundations
- Worked example: weak extension under one side
- Commissioning and verification
- Common ASD design errors on an exam
- How to study pressure-field design
The April 2026 NRSB RRS guide places mitigation theory and design near the start of its syllabus and gives active soil depressurization a central role. The aim is to lower pressure beneath the occupied space relative to the extraction system so soil gas is collected and routed outdoors before it enters the building. The system does not remove radon already in the room directly; it changes the pathway and pressure conditions that permit entry.
- Credential
- NRSB Radon Reduction (Mitigation) Specialist
- Topic
- Active Soil Depressurization Design and Pressure Fields
- Design principle
- Diagnose, design, install, verify and document
- Source guide
- NRSB Certification Exams Study Guide, April 2026 v1.1
The objective: control the soil-gas pressure relationship
ASD is an umbrella term. Common configurations include suction beneath a slab, a drain-tile network, a crawlspace membrane, a block wall or another foundation region. The name of the configuration describes where the system applies suction; the design still depends on whether the pressure field reaches the relevant area and whether the exhaust remains safe and effective.
A strong candidate thinks in sequence: investigate the foundation, choose a diagnostic location, evaluate communication, size the system using operating conditions and manufacturer data, install to applicable standards and codes, then verify performance. Memorizing a generic diagram without understanding the evidence behind it will not solve scenario questions.
Sub-slab communication and pressure-field extension
A pressure-field extension test assesses whether suction applied at a point can be detected at remote points beneath the slab. If a pressure change reaches multiple test points, the sub-slab material communicates sufficiently under the test conditions for that configuration to be considered. If remote points show little response, the design may need another suction point, a different location or more investigation.
The result depends on substrate, slab geometry, barriers, drainage features and the diagnostic setup. A porous aggregate bed may communicate differently from compacted soil or mixed fill. Moisture and obstructions can alter air movement. A preliminary diagnostic suction using a shop vacuum can indicate potential, but confirmatory testing with the properly excavated pit and a radon fan is a different and stronger check, as the NRSB outline notes.
A pressure measurement is local evidence. Place probes at meaningful remote locations and record their relation to the suction point, foundation zones and connected spaces. Avoid saying “the entire slab is under negative pressure” based on a single nearby port. The test plan should cover the areas that matter to the building and intended performance.
Choose suction locations from evidence
A suction point should serve the foundation zone where pressure control is needed while allowing a practical pipe route and discharge location. The ideal point is not always the geometric center or the most convenient place to drill. Consider sub-slab communication, room use, structural features, utilities, drainage, finished space and access before committing to an opening.
A suction pit increases the air volume available to the system and reduces resistance at the collection point. Its size and construction are governed by the applicable standard and site conditions. The RRS candidate should understand the purpose: create a functional collection region rather than simply make the largest possible hole. Excessive excavation can create hazards or damage utilities and must be avoided.
In a multi-zone foundation, one point may not communicate with every area. Diagnostic ports can reveal weak extension beneath a partition, addition or isolated footing. Multiple points can sometimes be balanced into one system, while separate systems may be needed in other circumstances. The design decision follows measured behavior and system constraints.
Understand pressure and airflow together
A pressure field and the system airflow are related but not interchangeable. A fan can move substantial air without creating useful pressure beneath the slab if the system has a large leak or poor connection. A strong static pressure at the suction pipe does not prove remote areas are controlled. Look for pressure response at the intended diagnostic points and confirm the system’s operating condition.
The fan operates on a curve relating airflow and static pressure. The connected pipe, pit, soil and exhaust path create resistance; the fan must operate at a point compatible with that system. Read the manufacturer performance data using the expected static pressure rather than selecting by a marketing label or free-air rating. The right match supports the needed pressure and flow with acceptable noise and energy use.
A system with more powerful equipment is not automatically better. Oversizing may increase noise, energy, exhaust concerns or short cycling without solving poor communication or a leak. Before changing a fan, determine whether the cause is restriction, bypass, weak extension, obstruction or another design flaw. Troubleshooting comes after system behavior is measured.
Negative-pressure sources and indoor safety
The NRSB outline asks for a walkthrough to assess sources of negative pressure. Exhaust fans, fireplaces, air handlers and other equipment can affect building pressure and combustion safety. They also help explain baseline radon entry. A mitigator should identify relevant equipment and consider how the new system interacts with the occupied building.
ASD exhaust should be routed to an acceptable outdoor location under the current standard and local code, away from openings and locations where re-entry is likely. Exact clearances and termination details belong to the current standard and code; do not rely on an unsourced number. The discharge plan is part of system design, not a finishing detail to improvise after the fan is installed.
Where combustion appliances are present, evaluate potential backdrafting or other hazards under the required procedure and use qualified personnel. The goal is to reduce radon without creating a separate indoor-air or combustion risk. Document the tests and corrective actions that applicable standards require.
Sealing and pressure field work together
Sealing visible openings can reduce bypass airflow, protect system performance and improve durability, but the NRSB guide says sealing alone usually does not solve radon. A pressure-control system targets the soil-gas entry mechanism. Seal decisions should be coordinated with diagnostic testing because a large bypass can dilute suction or allow soil gas to enter elsewhere.
Prioritize openings that interfere with the pressure boundary, such as gaps around suction piping, sump covers or penetrations, using materials appropriate to the condition and code. Do not block required drainage, combustion air or safety pathways. Some cracks move structurally or transmit water; a cosmetic seal may not last. Refer structural or water-intrusion problems to a qualified trade.
After sealing, recheck system behavior. If a change in leakage alters system resistance, pressure at remote points may change. Commissioning should verify the final configuration, not just the pre-seal test. Keep photographs or as-built notes that show where the system connects and which locations were sealed.
Plan a design for complex foundations
A basement with a slab, a crawlspace, a drain-tile loop and a block-wall foundation can contain multiple pressure zones. One suction point may draw effectively from one area while leaving another uncontrolled. Map those zones and test communication across the boundaries. Consider whether a membrane, block-wall suction or separate suction point is appropriate under the current standard and site facts.
Finished rooms can make ideal suction locations inaccessible. A pipe route may need to pass through closets, utility spaces or an exterior wall. Appearance matters to the client, but it cannot override safe routing, maintainability and performance. Discuss tradeoffs early: interior piping can be shorter; exterior piping may reduce intrusion indoors but face weather and aesthetic constraints.
When several points feed one fan, balance and pressure distribution matter. A system may require adjustments at branches or separate fans if zones have very different resistance. The NRSB guide specifically lists balancing systems between multiple suction points. Document what the final indicators show and explain how the owner can recognize normal operation.
Worked example: weak extension under one side
Suppose a diagnostic fan produces a clear pressure response near the test pit but little response beneath a remote slab extension. First confirm probe placement, instrument connection and diagnostic operating conditions. Then inspect for a footing, compacted fill, moisture or other barrier that could limit communication. Do not immediately substitute a higher-power fan; the limitation may be the substrate or the system path.
Test an alternative suction location or evaluate whether an additional point can reach the isolated zone. If the weak area is a distinct foundation, a separate strategy may be necessary. Compare each configuration using consistent conditions and record pressure response at remote points. After installation, verify indoor radon under the post-mitigation protocol as well.
An exam answer that says “add the largest fan” overlooks diagnosis. One that says “one suction pit always covers a home” ignores foundation diversity. The best choice uses evidence to address the specific weak zone and then checks both pressure control and radon reduction.
Commissioning and verification
Commissioning checks the installed system’s operating state, physical integrity, indicator function, pressure response where required, exhaust routing and safety conditions. Record fan model, suction locations, pipe layout and relevant test readings. The exact commissioning checklist comes from the current standard and contract. A fan running is only one item of evidence.
A post-mitigation radon measurement evaluates the outcome in occupied air. Use the applicable method and timing, and explain that a measurement represents its test period. If the result remains above the recommended or contractual target, investigate rather than assuming the system is finished. System adjustments and repeat tests should be documented.
Give the owner clear operating instructions: what the system does, which indicator to check, whom to call if it stops, and what maintenance or follow-up applies. Avoid claiming that a system guarantees a fixed concentration forever. Building changes, fan failure or new pathways can alter performance.
Common ASD design errors on an exam
Watch for answers that confuse fan suction with whole-building depressurization, place a point without considering extension, rely only on sealing, or treat one pressure reading as proof of success. Another trap is to choose a fan solely by pipe diameter or nominal airflow. System resistance and performance curve matter.
Questions may mention a shop vac, fully excavated pit, micromanometer, smoke or fan curve. Identify what each tool contributes: preliminary communication, confirmatory behavior, pressure measurement, qualitative airflow visualization or equipment selection. None alone proves final radon reduction in all rooms.
Good design is empirical. Diagnostic tests add time and can complicate a quote, but they often prevent repeat visits and underperforming systems. On the exam, favor evidence before irreversible installation decisions.
How to study pressure-field design
Draw a slab and add a suction point, remote test ports, a footing and an isolated addition. Predict which points might respond and what test would confirm your prediction. Then change the substrate from porous aggregate to dense soil and reassess. This exercise builds intuition without pretending that a drawing can replace field readings.
Study the current ANSI/AARST mitigation standard alongside the April 2026 NRSB guide. NRSB names diagnostic versus confirmatory pressure-field testing, substrate composition, suction-point number and location, manometers, fan curves and balancing. Learn those relationships, then use authorized standard text for procedural requirements.
For each practice question, state the evidence, the design decision and the verification step. This three-part answer catches overconfident distractors. The exam assesses whether a candidate can manage the full life cycle, not only identify a technology acronym.
The NRSB guide is a current exam outline and reference list. ANSI/AARST’s standard portal lists mitigation standards for existing homes and shared buildings. EPA’s consumer guide explains residential mitigation approaches. Exact installation clearances, electrical details, fan placement and performance criteria must come from the current standard, manufacturer instructions and local code.
This article teaches general engineering concepts; it does not provide a construction specification. Do not use it alone to design or install an operating radon system. Every project needs site-specific investigation and code-compliant work by qualified professionals.
The exam’s main design lesson is straightforward: test the pressure field, select the configuration supported by evidence, install safely and verify the indoor result. That sequence keeps a fan from becoming a substitute for engineering judgment.
Common questions
What does active soil depressurization do?
ASD applies suction beneath or beside the building to collect soil gas and exhaust it outdoors, reducing the opportunity for that gas to enter occupied space. The system must be designed for the actual foundation and verified after installation.
Does one pressure-field test prove the whole slab is covered?
No. A test supports a conclusion only for the measured points and conditions. Test remote areas that represent relevant zones, and use the current standard to determine the required diagnostic and confirmatory procedure.
Should a mitigator always choose a stronger fan when pressure is weak?
No. Weak extension may result from poor communication, an obstruction, a leak or a configuration problem. Diagnose the cause before changing equipment; a larger fan cannot fix every substrate or bypass issue.
Is sealing enough to mitigate radon?
Usually not by itself. NRSB’s study guide says sealing alone usually does not work. It may support an ASD system by reducing bypasses, but the design should address the soil-gas pressure pathway.