FCC GROL Elements 1 and 3: Antennas, Feed Lines and Transmission Loss
An antenna converts energy between guided RF and electromagnetic waves.
- The feed line carries RF between the radio and antenna, with losses and impedance effects along the way.
- GROL problems connect wavelength, antenna length, gain, polarization, line loss and standing-wave ratio.
On this page9 sections
Follow power to the antenna
Transmitter output, power at the end of the feed line and the radiated field are different measurements. Cable, connectors, matching components and the antenna can introduce loss. A favorable transmitter reading does not establish that all of that power becomes useful radiation.
On receive, the antenna collects a wave and the line conveys the signal to the receiver. Line loss reduces the signal before processing. An amplifier later in the path cannot recover signal-to-noise information already lost.
Identify whether a question concerns transmitter output, antenna input, directional gain or received strength. The quantities are related but cannot be substituted for one another.
Wavelength and electrical length
For free space, wavelength in meters is approximately 300 divided by frequency in megahertz. At 150 megahertz, wavelength is about 2 meters. A quarter wavelength is 0.5 meter and a half wavelength is 1 meter.
These are electrical free-space lengths. A practical antenna can differ because of conductor diameter, end effects, loading and surroundings. Increasing frequency reduces wavelength; doubling frequency halves it.
Propagation in a cable is slower than in free space. Velocity factor is the ratio of cable propagation speed to free-space speed. A line with velocity factor 0.66 has a quarter-wave length equal to 0.66 times the corresponding free-space length.
For the 150 megahertz example, that cable section is 0.66 × 0.5 = 0.33 meter. Use velocity factor for the medium specified, rather than applying a cable factor indiscriminately to every antenna dimension.
Common patterns
An ideal half-wave dipole radiates most strongly broadside to its axis and weakly along its axis. Its radiation pattern is not a sphere of equal strength in every direction.
A quarter-wave vertical commonly works with a ground plane or suitable counterpoise. The return path is part of the antenna system. Changing it can change impedance, efficiency and pattern.
A directional array concentrates radiation toward selected directions. A Yagi uses driven and parasitic elements. A parabolic reflector with a suitable feed can produce a narrow beam. Gain in one direction comes with reduced radiation elsewhere.
An omnidirectional antenna is usually omnidirectional in a particular plane. A vertical antenna may give broad azimuth coverage while still having an elevation pattern with stronger and weaker directions.
Gain and polarization
Gain compares radiation in a stated direction with a reference. dBi uses an isotropic reference; dBd uses a half-wave dipole reference. Their numbers cannot be compared as though the reference were identical.
An antenna does not create transmitter energy. It redistributes radiation and may have efficiency losses. Directional gain helps only when the useful path lies in the intended part of the pattern.
Polarization describes the orientation or behavior of the electric field. A simple vertical antenna produces primarily vertical polarization in its intended arrangement. A horizontal antenna produces primarily horizontal polarization.
An ideal receiving antenna at right angles to a linearly polarized field has poor coupling. Reflections can alter polarization, so practical isolation is not necessarily infinite. Use the ideal or practical conditions specified in the question.
Circular polarization involves a rotating field orientation with a defined sense. A circular-looking piece of metal is not enough to establish circular polarization; the antenna design and excitation matter.
Characteristic impedance
Coaxial cable has an inner and outer conductor separated by a dielectric. Characteristic impedance follows geometry and dielectric properties. Many radio systems use a nominal 50 ohm line.
Characteristic impedance is not the conductor’s DC resistance. A short length of sound coax can have very low resistance along its conductors while still having 50 ohm characteristic impedance.
A matched termination minimizes reflections in the ideal model. A mismatch sends part of the wave back toward the source. The forward and reflected waves combine to form a standing-wave pattern.
A matching network can transform impedance at its measurement point. Low transmitter-end SWR does not prove low cable loss or high antenna radiation efficiency.
Standing-wave ratio
With reflection coefficient magnitude |Γ|, SWR = (1 + |Γ|)/(1 − |Γ|). An ideal match has |Γ| = 0 and SWR 1:1.
For SWR 3:1, |Γ| = (3 − 1)/(3 + 1) = 0.5. Reflected power fraction at that reference point is |Γ|² = 0.25, or 25 percent. Voltage reflection magnitude and reflected power fraction are different numbers.
That fraction is not automatically the transmitter power permanently lost as heat. Source behavior, multiple reflections, cable loss and termination determine delivered power. Apply the simplified model only where the problem supports it.
A lossy line attenuates a reflected wave on its return trip. It can make transmitter-end SWR appear better despite a poor antenna match. SWR alone therefore cannot measure overall antenna performance.
Decibel loss
Power loss is 10 log10(Pin/Pout). A 3 dB loss leaves approximately half the power; 6 dB leaves approximately one quarter; 10 dB leaves one tenth.
With 100 watts entering a matched line having 3 dB loss, about 50 watts leaves it. Another 3 dB loss leaves about 25 watts. Decibel losses add, while linear power fractions multiply.
For greater precision, Pout = Pin × 10^(−loss/10). Use 20 log10 for a voltage or current ratio only under the impedance conditions that make it correspond to the intended power ratio.
Cable attenuation generally increases with frequency and length. Actual performance also depends on construction, condition and installation. Water ingress and poor connectors can add both loss and mismatch.
A simple budget
Suppose transmit antenna gain is 10 dB, transmit cable loss is 3 dB, receive antenna gain is 10 dB and receive cable loss is 2 dB, with compatible gain references. Their combined contribution is 10 − 3 + 10 − 2 = 15 dB.
Propagation loss and other terms still belong in the full link budget. This calculation alone cannot establish received power or reliable range. It illustrates why gain and loss need the correct signs.
Mixing dBi and dBd without converting references introduces an error. Adding cable loss as a positive gain reverses its effect. Each number needs a reference and a measurement location.
Diagnose the external system
A transmitter operates normally into a suitable dummy load but shows high reflected power on its installed antenna. The contrast points toward the cable, connectors, matching arrangement or antenna. It does not identify which one failed.
The dummy load needs suitable impedance, frequency range and power rating. It absorbs RF rather than intentionally radiating it, demonstrating that an excellent match is compatible with little useful radiation.
A connector fault may cause loss and mismatch. A damaged cable may attenuate forward and reflected waves. Nearby metal can alter antenna impedance and pattern. Measurements at defined points distinguish these causes.
Keep four questions separate: how much power leaves the transmitter, how much reaches the antenna, how efficiently it radiates, and where the energy goes. One favorable reading cannot answer all four.
Common questions
Does gain create power?
No. It describes directional radiation relative to a reference and reflects pattern concentration and efficiency.
Does 1:1 SWR prove good radiation?
No. A dummy load can be well matched while radiating very little. A lossy cable can also hide a mismatch.
What remains after 3 dB loss?
Approximately half the input power. The exact fraction is 10^(−3/10).
Why use velocity factor?
It determines electrical wavelength inside a transmission line, making physical quarter-wave cable sections shorter than their free-space equivalents.