FCC GROL Elements 1 and 3 Original Questions and Answers
These original GROL practice questions cover operating rules, electrical calculations, circuits, modulation, antennas, propagation and diagnosis.
- Each includes a worked explanation.
- They are study exercises for Elements 1 and 3, not copied pool questions or a complete 124-question examination.
On this page20 sections
- How to use these questions
- 1. A routine call
- 2. Digital selective calling
- 3. Distress information
- 4. Current through a resistor
- 5. Resistor power
- 6. Parallel resistance
- 7. A loaded divider
- 8. RMS and peak
- 9. Capacitive reactance
- 10. Circuit coupling
- 11. AM sidebands
- 12. An FM bandwidth estimate
- 13. Receiver image
- 14. Wavelength
- 15. Feed-line loss
- 16. SWR and reflected power
- 17. Propagation gap
- 18. A transmitter comparison
- Review by error type
How to use these questions
Try each problem before reading its answer. Write calculations with units, and give a one-sentence reason for procedure questions. A correct guess still belongs in review if you cannot explain it.
The set is deliberately varied. It samples important concepts rather than reproducing the official topic distribution or predicting a score. Element 1 and Element 3 pass requirements remain separate: 18/24 and 75/100.
For technical examples, use the assumptions in the question. Ideal components and matched lines simplify the model. Do not invent a fault or loss that the stem has not included.
After review, change one numerical value or operating fact and solve again. That tests transfer of understanding beyond the original answer.
1. A routine call
Two vessels establish a routine voice call on marine VHF channel 16. They now want to discuss detailed meeting arrangements. What is the appropriate next action? A: Continue the whole discussion on channel 16. B: Move to a suitable working channel. C: Continue by voice on channel 70. D: Begin using the distress signal to keep the channel clear.
Answer: B. Channel 16 serves distress, safety and calling functions. A routine exchange should move to a suitable working channel after contact rather than occupy it for a long discussion.
C confuses voice with DSC, while D misuses a distress signal. A reflects the correct initial calling context but the wrong continuing use. The key distinction is establishing contact versus carrying on routine traffic.
2. Digital selective calling
An operator proposes testing a microphone by making a voice transmission on channel 70. Which description fits the problem? A: The channel is for DSC rather than voice. B: Voice is allowed only if power is increased. C: Voice is allowed only if the call is short. D: The channel is reserved for SSB voice.
Answer: A. Channel 70 is a digital selective calling channel. A change in output power or duration does not correct a wrong-mode transmission.
This question tests channel function, not signal strength. A radio capable of transmitting on a frequency does not make every use of that frequency appropriate.
3. Distress information
A vessel is in grave and imminent danger and needs immediate assistance. Which message content best supports a response? A: Only repeated MAYDAY calls. B: Vessel identity, position, nature of distress and assistance needed. C: A long account of the entire voyage before giving location. D: A request for routine marina information.
Answer: B. The distress signal establishes priority, while identity, location and the specific need allow assistance to be directed.
A leaves out actionable information. C delays it. D describes a different communication purpose. Clear factual content matters alongside correct signaling.
4. Current through a resistor
An ideal 600 ohm resistor has 12 volts across it. What current flows? A: 20 amperes. B: 2 amperes. C: 20 milliamperes. D: 0.2 milliamperes.
Answer: C. I = V/R = 12/600 = 0.02 amperes, or 20 milliamperes.
A is a prefix error: the numerical value 20 needs milliamperes. A quick plausibility check also helps. A 600 ohm resistor across a modest voltage is not drawing tens of amperes.
5. Resistor power
Using the same 12 volt, 600 ohm resistor, what power is dissipated? A: 0.24 watts. B: 240 watts. C: 7,200 watts. D: 50 watts.
Answer: A. P = V²/R = 144/600 = 0.24 watts. Alternatively, use P = VI = 12 × 0.02.
B can result from inserting 20 milliamperes as 20 amperes. C multiplies voltage by resistance, which does not produce watts. The requested dissipated power is distinct from a practical choice of rated component.
6. Parallel resistance
Two ideal 600 ohm resistors are connected in parallel. What is their equivalent resistance? A: 1,200 ohms. B: 600 ohms. C: 300 ohms. D: 1,800 ohms.
Answer: C. For two equal resistors in parallel, equivalent resistance is half either value. Using the general expression gives 600 × 600/(600 + 600) = 300 ohms.
A uses the series rule. An equivalent parallel resistance smaller than the smallest branch is the expected trend. If your calculation produces a larger value, reconsider the connection model.
7. A loaded divider
Two 10 kilohm resistors form a divider across 12 volts. A 10 kilohm load is connected across the lower resistor. What is the ideal output across that lower combination? A: 12 volts. B: 8 volts. C: 6 volts. D: 4 volts.
Answer: D. The lower resistor and load are parallel, giving 5 kilohms. The divider output is 12 × 5/(10 + 5) = 4 volts.
Six volts would be the unloaded result. The new load changed the network, so applying the original equal-resistor ratio ignores a stated condition.
8. RMS and peak
A sinusoidal voltage centered on zero has a peak value of 10 volts. What is its RMS value? A: Approximately 7.07 volts. B: 20 volts. C: 10 volts. D: Approximately 14.14 volts.
Answer: A. For a sine wave, Vrms = Vpeak/√2 = 10/1.414, approximately 7.07 volts.
B is the peak-to-peak value. The waveform specification is necessary: the same peak-to-RMS factor should not be applied automatically to square waves or pulse trains.
9. Capacitive reactance
An ideal capacitor’s frequency increases tenfold while capacitance stays unchanged. What happens to its reactance? A: It increases tenfold. B: It decreases to one tenth. C: It stays constant. D: It becomes ordinary DC resistance.
Answer: B. XC = 1/(2πfC), so reactance is inversely proportional to frequency.
A describes the direction of change for inductive reactance, not capacitive reactance. The question can be solved without numerical values because it asks for a ratio and holds capacitance constant.
10. Circuit coupling
A receiver’s detector and audio amplifier have normal separate DC bias readings, but an open capacitor connects their signal path. What is a plausible consequence? A: The AC signal cannot pass through that coupling path. B: The capacitor forces twice the supply voltage onto the speaker. C: The receiver’s antenna becomes longer. D: DC bias readings prove the signal path is intact.
Answer: A. A coupling capacitor carries the AC signal while separating DC conditions. If it opens, the intended signal path is interrupted even though separate DC readings may remain normal.
D makes a measurement-category mistake. A DC bias test and an AC signal-path test do not establish the same thing.
11. AM sidebands
A conventional AM carrier is at 2 megahertz and is modulated by a single 2 kilohertz tone. Where are the sidebands? A: 2 kilohertz and 4 kilohertz. B: 4 megahertz and 6 megahertz. C: 1.998 megahertz and 2.002 megahertz. D: Both exactly at 2 megahertz.
Answer: C. Convert 2 kilohertz to 0.002 megahertz, then subtract and add it to the carrier.
B describes harmonic-related multiples rather than modulation offsets. A names audio-frequency values. The correct answer keeps the carrier and message frequency distinct.
12. An FM bandwidth estimate
An FM signal has maximum deviation of 2.5 kilohertz and highest modulating frequency of 3 kilohertz. What does Carson’s rule estimate? A: 5.5 kilohertz. B: 11 kilohertz. C: 1.5 kilohertz. D: 2.5 megahertz.
Answer: B. The estimate is 2 × (deviation + highest modulating frequency) = 2 × (2.5 + 3) = 11 kilohertz.
A omits the factor of two. D introduces a unit error. Carson’s rule is an approximation; it is not a statement of the channel assignment or a regulatory emission limit.
13. Receiver image
A wanted signal at 10 megahertz mixes with a 10.455 megahertz local oscillator to produce a 455 kilohertz IF. Which other RF frequency can produce the same difference IF in this high-side arrangement? A: 10.910 megahertz. B: 455 megahertz. C: 20 megahertz. D: 1 kilohertz.
Answer: A. The image is 455 kilohertz above the oscillator: 10.455 + 0.455 = 10.910 megahertz.
Both wanted and image can convert to the same IF. Front-end RF rejection matters because an IF filter cannot later distinguish two original RF frequencies already converted to the same value.
14. Wavelength
What is the approximate free-space wavelength of a 150 megahertz signal? A: 150 meters. B: 0.5 meter. C: 2 meters. D: 300 meters.
Answer: C. Wavelength in meters is approximately 300/frequency in megahertz, giving 300/150 = 2 meters.
B is the quarter wavelength at that frequency, not the full wavelength. Antenna-dimension questions often depend on reading which fraction is requested.
15. Feed-line loss
A transmitter supplies 40 watts to a matched feed line having 3 dB loss. Approximately how much reaches the other end? A: 37 watts. B: 80 watts. C: 20 watts. D: 3 watts.
Answer: C. A 3 dB loss leaves approximately half the power, giving about 20 watts. The exact expression is 40 × 10^(−3/10), also close to 20.
A subtracts decibels as though they were watts. B treats loss as gain. The result concerns cable output, not antenna radiation efficiency or received power at a distant station.
16. SWR and reflected power
At a defined measurement point, an idealized system has SWR 3:1. What is the reflected power fraction there? A: 50 percent. B: 25 percent. C: 75 percent. D: 3 percent.
Answer: B. Reflection coefficient magnitude is (3 − 1)/(3 + 1) = 0.5. Power fraction is its square: 0.5² = 0.25.
A confuses voltage reflection magnitude with power fraction. The fraction at the point is not automatically the entire system’s power permanently lost as heat.
17. Propagation gap
An HF station is received strongly at a distant location but poorly at a nearer location beyond useful ground-wave coverage and before the first sky-wave return. Which concept fits? A: Skip zone. B: Perfect omnidirectional coverage. C: Increased DC resistance. D: A mandatory receiver fault.
Answer: A. The geometry can leave a region between useful ground-wave reception and the first sky-wave return.
The observation does not prove a receiver defect. Greater distance does not always mean weaker reception when propagation mechanisms create different coverage regions.
18. A transmitter comparison
A transmitter works normally into a suitable dummy load but shows abnormal reflected power on its installed antenna. Which investigation follows most directly? A: Replace the microphone immediately. B: Examine the feed line, connectors, matching and antenna. C: Conclude that every internal stage has failed. D: Ignore reflected power because forward output exists.
Answer: B. The comparison separates load conditions and points toward the external RF system.
It does not prove which external component is defective. A sound diagnosis chooses the next measurements rather than turning a plausible section into an unsupported one-part conclusion.
Review by error type
If you missed a calculation, identify whether the problem was selecting the relationship, converting units or carrying out arithmetic. If you missed a circuit question, trace the actual connections before repeating the calculation.
If you missed an operating question, name the rule distinction. Routine versus distress and voice versus DSC need different remedies from a simple forgotten numerical value.
Then solve a fresh example in the same category. A repaired skill should survive changed values or wording. Retaking this exact set immediately mainly tests short-term memory.
Use broader mixed practice before judging readiness. This set teaches selected concepts and does not provide a statistically valid pass prediction or a complete official paper.
Common questions
Are these copied official questions?
No. They are original instructional questions with worked answers.
Is this a full mock exam?
No. It is an 18-question worked practice set covering selected concepts, not the complete 124-question pair.
Can I average the two elements when scoring practice?
Keep results separate because Element 1 and Element 3 must each meet their own threshold.
What should I do with a correct guess?
Review the explanation and solve a fresh related problem until you can state why the answer fits.