Sitonce
Country: US
Show exams for United States Hong Kong
Sign in

Noise Exposure and Hearing Protection: OHST Exam

Updated 10 min read
Key takeaway

Noise risk depends on sound level and duration.

  • OSHA general-industry rules set an 85 dBA eight-hour TWA action level and a 90 dBA permissible exposure limit.
  • NIOSH recommends control below an equivalent 85 dBA eight-hour exposure.
  • Use the right standard, monitoring method and hearing protection.
On this page13 sections
  1. Decibels are logarithmic
  2. Understand OSHA action level and PEL
  3. Worked example: selecting the next action
  4. Control noise at its source
  5. Monitoring and hearing conservation
  6. A noise assessment checklist
  7. Worked example: mixed noise exposure
  8. Choose and verify engineering and administrative controls
  9. Manage the hearing conservation program
  10. NIOSH uses a different exchange rate
  11. Choose a protector that workers can use correctly
  12. Use audiometry as program feedback
  13. Use the worker perspective in control evaluation
OSHA general-industry action level
85 dBA as an 8-hour TWA
OSHA general-industry PEL
90 dBA as an 8-hour TWA
OSHA exchange rate
5 dBA
NIOSH recommendation
Below an equivalent 85 dBA 8-hour exposure
Impulsive or impact noise
OSHA limit 140 dB peak sound pressure level

Decibels are logarithmic

Sound level is measured on a logarithmic decibel scale. A few decibels can represent a substantial change in sound energy and exposure dose, so averaging decibel values as if they were ordinary linear numbers can produce a wrong result. OSHA uses a 5 dBA exchange rate in its general-industry standard: each 5 dBA increase halves the allowable exposure time for the same dose.

The exact calculation method depends on the applicable standard and instrument. A technician should know the difference between a sound level at a moment, an eight-hour time-weighted average and a noise dose. Personal dosimeters can measure a worker's exposure over a shift; sound level meters can characterize locations or tasks. Select the tool based on the question.

NIOSH recommends controlling worker noise exposure below a level equivalent to 85 dBA for eight hours to minimize noise-induced hearing loss. That recommendation is not the same legal threshold as OSHA PEL. A responsible report labels each value and source rather than saying “the limit is 85” without context.

Understand OSHA action level and PEL

For general industry, OSHA 29 CFR 1910.95 requires a continuing effective hearing conservation program when employee noise exposure equals or exceeds an eight-hour TWA of 85 dBA, also called the action level. The standard also establishes a permissible exposure limit of 90 dBA for an eight-hour day under its specified calculation approach.

These thresholds trigger different obligations and should not be collapsed. At or above the action level, the hearing conservation program includes monitoring, audiometric testing, hearing protectors, training and evaluation requirements under the standard. Where exposure exceeds the PEL, feasible engineering or administrative controls are required, with hearing protection in addition where controls are insufficient. Read the full current standard for exact duties.

Construction rules differ from general industry. Do not transfer a general-industry threshold without checking the applicable standard and work context. State-plan requirements may also apply. For an exam question, identify the stated industry and rule; for a real workplace, verify jurisdiction, task and current regulation.

Worked example: selecting the next action

A machine operator has an eight-hour TWA of 86 dBA in general industry. The result is above the 85 dBA action level and below the 90 dBA PEL. The appropriate response includes the hearing conservation program steps that apply at the action level, such as continued monitoring, audiometric testing and training, plus evaluating whether source controls can reduce exposure. It is not accurate to say there is no duty because the result is below the PEL.

A second worker has 92 dBA eight-hour TWA. The result exceeds the general-industry PEL. Evaluate and implement feasible engineering or administrative controls under the standard and use hearing protection as required. Do not jump to “earplugs solve it” without fit, training, maintenance and attenuation considerations.

These examples simplify the regulatory application for learning. Actual compliance depends on the standards calculation and measurement rules, instrument settings, exposure pattern and jurisdiction. Refer to OSHA 1910.95 and the employer hearing conservation program.

Control noise at its source

Engineering controls can reduce sound generation or transmission: maintain equipment, isolate vibration, enclose a source, install barriers or select quieter processes where feasible. Administrative measures can reduce time at high-noise tasks, but they must be designed and managed so exposure is actually reduced. Controls should be checked after installation and maintained as equipment changes.

Work practices matter. Keep guards and enclosures in place, avoid unnecessary compressed-air noise, report damaged equipment and follow safe operating procedures. A control that is removed for convenience or fails to cover the actual source may provide little protection. Worker input can identify conditions that a one-time survey misses.

Hearing protection complements controls. Select protectors for the hazard and worker, ensure fit and compatibility with other PPE, provide training and replace damaged items. A nominal attenuation label does not prove the worker receives that attenuation in practice. The employer program should evaluate protectors and make changes when conditions or tools change.

Monitoring and hearing conservation

When information suggests exposure may reach the action level, OSHA requires a monitoring program under the standard. Monitoring should identify affected employees and reflect actual work patterns. Reassess when process, equipment, schedule or controls change. Personal dosimetry can capture variable exposure across a shift, while a sound level survey can help locate sources and prioritize controls.

The hearing conservation program includes audiometric testing, hearing protection, training and evaluation requirements. A baseline audiogram and periodic audiograms are handled through the standard and qualified providers. A technician should protect employee medical information and not diagnose hearing loss from a screening record.

Review indicators such as participation, timely audiometry, worker-reported protector problems and exposure trends. An effective program measures implementation and outcomes. Do not treat distribution of earplugs alone as proof that the noise hazard is controlled.

A noise assessment checklist

Identify tasks and employees, including intermittent work, maintenance and nearby operations. Determine whether the question concerns general industry, construction or another context. Select equipment and settings suited to the task, calibrate as required and collect representative personal or area data. Document source, duration, controls, worker position and relevant changes.

Interpret the data against the right period and threshold. Compare the eight-hour TWA to the action level and PEL where appropriate. Consider short-duration peaks or impulsive noise separately. State uncertainties and avoid comparing a spot reading directly with an eight-hour TWA.

Recommend controls in order of effectiveness and state how to verify them. If the measurement or control design is beyond competence, consult an occupational hygienist or acoustics specialist. Document communication, hearing protection and follow-up responsibilities.

Worked example: mixed noise exposure

OSHA Table G-16 gives eight hours at 90 dBA and four hours at 95 dBA. For mixed exposure, compare each actual duration C with its permitted duration T, then add the fractions. A sum above one exceeds the table limit. The calculation combines time allowances, rather than taking an arithmetic average of the sound levels.

Task exposureActual time CTable time TFraction C/T
95 dBA2 hours4 hours0.50
90 dBA4 hours8 hours0.50
Combined example1.00

In this simplified example, the two tasks together use the full table allowance. If the 95 dBA task instead lasts three hours, the sum becomes 3/4 + 4/8 = 1.25, above the limit. A complete assessment must account for every relevant exposure period, not just the two tasks shown. Additional exposure can change the result.

Do not subtract a protector rating from the readings before deciding whether hearing conservation applies: OSHA assesses that threshold without credit for personal protective equipment. Peak noise also needs separate attention; the standard states that impulsive or impact noise should not exceed 140 dB peak sound pressure level.

Choose and verify engineering and administrative controls

Start by identifying the loudest source and how sound reaches the worker. Engineering controls can include quieter equipment, maintenance, vibration isolation, enclosure, barriers and acoustic treatment when appropriate. Barriers must not block ventilation or create new mechanical hazards. Check that the source is actually controlled during the task, not merely when equipment is idle.

Administrative controls can reduce exposure duration through task rotation, restricted access or scheduling, but they must reduce the actual worker dose and not transfer risk to others. They may be less reliable than source controls and can create productivity pressure. Verify procedures and worker practice.

Reassess after controls or equipment changes. Compare measurements using the same method and representative conditions. Ask workers whether the modification interferes with communication, alarms or task performance. A control that compromises warning signals or is removed for convenience needs redesign.

Manage the hearing conservation program

At or above the OSHA general-industry 85 dBA eight-hour TWA action level, the standard requires an effective hearing conservation program. Program elements include monitoring, audiometric testing, hearing protectors, training and evaluation, subject to the detailed requirements. Maintain records and identify affected workers. Use the current standard text for specific testing schedules and duties.

Audiometric testing is handled by qualified providers and should be treated as confidential health information. A technician may support program coordination but should not diagnose hearing loss. A standard threshold shift or concerning pattern should be handled through the program and professional review.

Training should explain the hazard, controls, correct protector use, fit and maintenance. Evaluate understanding and availability. If a worker reports discomfort or poor fit, offer evaluation rather than assuming the protector is used correctly. The purpose is effective protection, not a completed sign-in sheet.

NIOSH uses a different exchange rate

NIOSH recommends an 85 dBA eight-hour limit with a three-decibel exchange rate. Each 3 dBA increase halves the exposure duration. The resulting sequence is 85 dBA for eight hours, 88 dBA for four, 91 dBA for two and 94 dBA for one. These are health-based recommendations, distinct from OSHA general-industry table allowances.

For an original calculation, two hours at 91 dBA uses the entire NIOSH recommended daily allowance at that level. Another hour of hazardous exposure cannot be dismissed just because the task ended early in the shift. Identify the stated criterion before calculating; using the five-decibel OSHA rate in a NIOSH problem produces the wrong answer.

A dosimeter report should identify its criterion level, exchange rate, threshold and measured duration. Two instruments can display different dose percentages for the same sound exposure when configured to different criteria. Compare like settings and label the standard used; a bare “100% dose” is incomplete without that context.

Industry and jurisdiction also matter. This article uses the federal OSHA general-industry standard for its regulatory examples. Other applicable rules must be checked separately; neither a classroom calculation nor a NIOSH recommendation substitutes for that review.

Choose a protector that workers can use correctly

Hearing protection should be selected for the measured hazard and work conditions. Consider attenuation, comfort, fit, compatibility with other PPE, communication needs, alarm audibility and hygiene. A product with a high rating may not perform as labeled when inserted incorrectly or worn inconsistently.

Provide instruction and hands-on fitting support where required by the program. Replace damaged or contaminated protectors. Reassess after a worker complaint, process change or updated exposure result. Do not assume an employee uses a protector merely because it was issued.

For workers who need to hear warning signals or communicate, select controls that preserve necessary communication. Engineering changes may be safer than relying on hearing protectors alone.

Use audiometry as program feedback

Audiometric results can help evaluate whether the hearing conservation program is effective, but they are handled by qualified providers and do not replace exposure control. A technician should follow the standard and program for baseline and periodic testing, referral and recordkeeping. Protect medical information.

A pattern of hearing changes can trigger review of noise measurements, protector fit, training and controls. It does not prove a single cause on its own. Coordinate with occupational health professionals and do not diagnose.

Program evaluation should include both exposure data and worker feedback. If hearing protection is uncomfortable or workers cannot hear instructions, the solution may require a different protector or stronger engineering control.

Use the worker perspective in control evaluation

Ask whether a control is usable, whether alarms remain audible and whether the work can be completed without bypassing protection. Workers often identify practical barriers that a measurement alone cannot show. Use that feedback alongside dosimetry and source evaluation.

A protector that is uncomfortable or interferes with another required item may be worn inconsistently. Reassess fit and options while maintaining the applicable program. The goal is effective hearing protection and reduced exposure, not merely distributing equipment.

Common questions

At what level does OSHA require a general-industry hearing conservation program?

At an 85 dBA eight-hour TWA action level under 29 CFR 1910.95.

Is the OSHA action level the same as the PEL?

No. The general-industry PEL is 90 dBA as an 8-hour TWA.

Is NIOSH 85 dBA an OSHA limit?

No. NIOSH recommends it; OSHA standards have their own legal thresholds.

Are decibels linear?

No. Decibels use a logarithmic scale.