Sitonce
Country: US
Show exams for United States Hong Kong
Sign in

OHST Exam Sample Questions and Answers

Updated 11 min read
Key takeaway

This original OHST-style practice set teaches how to connect a work scenario to a hazard, evidence and control.

  • It is not an official or recalled BCSP question.
  • For each answer, identify the fact that drives the choice, show calculations with units, and distinguish a legal OSHA requirement from a NIOSH recommendation.
On this page15 sections
  1. Question 1: calculate a time-weighted average
  2. Question 2: choose representative sampling
  3. Question 3: select a control for an emission source
  4. Question 4: interpret a noise program trigger
  5. Question 5: control unexpected startup
  6. Question 6: identify chemical information
  7. Question 7: calculate an incidence rate
  8. Question 8: investigate a ventilation change
  9. How to review an answer
  10. Build original questions from the blueprint
  11. Question 9: evaluate training effectiveness
  12. Question 10: respond to a near miss
  13. Question 11: communicate an evacuation
  14. Question 9: evaluate training effectiveness
  15. Use answer explanations to connect domains

Question 1: calculate a time-weighted average

Example question

A worker experiences 18 mg/m³ for 2 hours and 6 mg/m³ for 6 hours. What is the 8-hour TWA?

  1. A. 6 mg/m³
  2. B. 9 mg/m³
  3. C. 12 mg/m³
  4. D. 24 mg/m³
Answer: B. Compute (18×2 + 6×6) ÷ 8 = (36 + 36) ÷ 8 = 9 mg/m³. The denominator is the full eight-hour shift. The worked example assumes complete interval coverage and is not a compliance determination for a real substance.

The answer is B. Weight each concentration by its duration: 18×2 equals 36 concentration-hours; 6×6 equals 36. Their sum is 72, divided by eight hours, or 9 mg/m³. A common distractor is to take the unweighted average of 18 and 6, which gives 12 but ignores that the lower exposure lasted longer.

Before comparing a calculated value with a standard, verify the relevant chemical, measurement method, limit and averaging period. This original practice problem uses a simple full-shift TWA and should not be used as a workplace exposure assessment.

Question 2: choose representative sampling

Example question

Which approach best assesses an individual cleaner exposure?

  1. A. Use only a distant fixed-area reading
  2. B. Use appropriate representative personal breathing-zone sampling
  3. C. Replace air monitoring with a bulk liquid sample
  4. D. Compare a short reading directly to an eight-hour TWA
Answer: B. A personal breathing-zone sample is positioned to represent air inhaled by the worker, using a method suitable for the agent and task. Area or bulk samples can answer different questions but do not automatically represent individual exposure.

The answer is B. The question asks about the individual cleaner, so personal breathing-zone sampling is the most directly relevant approach when properly selected and conducted. OSHA distinguishes personal, area and bulk samples. A bulk sample can identify material composition; it does not substitute for inhaled concentration. A short-duration result should not be compared to an eight-hour limit without matching the standard averaging period.

The sample plan still needs a qualified method, representative task timing, calibration and appropriate laboratory analysis. If the agent or tank condition is unknown, protect workers and consult the site procedure and a competent industrial hygienist before entry or sampling.

Question 3: select a control for an emission source

Example question

A local exhaust hood is far from a welding-fume source. What is the best improvement?

  1. A. Place the hood close enough to capture emissions before they cross the breathing zone and verify function
  2. B. Blow room air toward the worker
  3. C. Issue an unselected disposable mask
  4. D. Take one area sample and make no change
Answer: A. Local exhaust is intended to capture contaminants at the source and prevent dispersion through the breathing zone. OSHA technical guidance emphasizes hood location and operation. PPE may be necessary but does not correct a poorly positioned engineering control.

The answer is A. OSHA ventilation guidance says a local exhaust hood should be placed close to the source and arranged so contaminants are not drawn through the worker breathing zone. General airflow toward a worker may worsen exposure. Respiratory protection is selected under a program and does not replace fixing a defective engineering control when feasible.

After adjustment, verify airflow and worker protection under the applicable procedure. Consult a ventilation specialist if hood design, capture velocity or system balance is uncertain.

Question 4: interpret a noise program trigger

Example question

A general-industry worker reaches 85 dBA as an 8-hour TWA. What does this indicate?

  1. A. Hearing-conservation action level applies
  2. B. Any earplug makes the exposure harmless
  3. C. The exposure is below all thresholds
  4. D. Hearing loss is proven
Answer: A. OSHA 29 CFR 1910.95 sets an 85 dBA eight-hour TWA action level for hearing conservation program requirements. The result does not diagnose hearing loss, and hearing protectors must be appropriately selected and managed.

The answer is A. OSHA requires an effective hearing-conservation program when general-industry noise exposure reaches an eight-hour TWA of 85 dBA. The OSHA permissible exposure limit is a distinct value, and NIOSH recommends controlling exposure below its own recommended level. Do not conflate action level, PEL and health recommendation.

A technician should use the applicable standard, measurement strategy and hearing conservation program. Hearing protection needs proper selection, fit, training, maintenance and evaluation; simply issuing a plug alone does not show adequate attenuation.

Question 5: control unexpected startup

Example question

A worker is repairing a jammed conveyor. Which approach best controls unexpected startup during servicing?

  1. A. Tell coworkers not to touch the switch
  2. B. Follow the applicable hazardous-energy control procedure, isolate and verify energy control
  3. C. Place a warning sign near the conveyor
  4. D. Rely on the emergency stop button
Answer: B. Hazardous-energy control requires an applicable isolation procedure and verification. A warning or emergency stop alone may not control stored or alternate energy.

The central issue is energy isolation during servicing. Communication and signage can support the process but do not replace the required energy-control procedure. The technician should identify all energy sources, follow the employer procedure and verify the equipment is in a safe state before work. Real tasks must follow the applicable OSHA standard and site-specific program.

Question 6: identify chemical information

Example question

A task involves a corrosive cleaner. Which source is the best starting point for chemical hazard and exposure information?

  1. A. Product label and safety data sheet, followed by current OSHA and NIOSH references as needed
  2. B. An unrelated solvent exposure table
  3. C. A worker opinion about odor only
  4. D. A historical internet post
Answer: A. Identify the actual product and constituents first, then consult relevant authoritative exposure and control information. Odor does not quantify exposure.

A label and safety data sheet can help identify the product and hazards, while the NIOSH Pocket Guide and OSHA materials can provide additional information. Confirm the current standard and measurement method for the substance. The information source must match the chemical. If the product identity or exposure conditions are uncertain, protect workers and obtain competent industrial hygiene support.

Question 7: calculate an incidence rate

Example question

A supervisor wants to compare a department rate with an industry benchmark. Which denominator best matches OSHA incidence-rate arithmetic?

  1. A. Number of safety meetings
  2. B. Employee hours worked over the same period
  3. C. Number of machines
  4. D. Number of months since the last incident
Answer: B. OSHA incidence rate calculation uses case count multiplied by 200,000 divided by employee hours worked for the same period.

The numerator and denominator need matching time periods and case definitions. The 200,000 constant normalizes the result to 100 full-time equivalent employees. A rate can support comparison when populations and work are comparable, but a small establishment can show large swings from one case.

Question 8: investigate a ventilation change

Example question

Workers report that an exhaust hood no longer captures smoke after a process change. What should the technician do?

  1. A. Close the concern because the fan still runs
  2. B. Verify system and process conditions, protect workers, and obtain competent evaluation
  3. C. Replace the hood with a dust mask
  4. D. Take an unrelated annual survey
Answer: B. A running fan does not prove capture. Evaluate the source, hood, airflow and worker exposure after the change; use protective actions and specialist support as needed.

The process change may have altered emission rate, hood position or airflow. Investigate safely, check system indicators and observe the task under representative conditions. If exposure may be uncontrolled, use the site response and protective procedure. A qualified ventilation or industrial hygiene professional may need to assess performance and select a corrective design.

How to review an answer

For every item, write a one-sentence reason the best answer fits the question. Then label the strongest distractor and explain why it is incomplete or mistimed. This prevents the learner from treating practice as answer memorization. Keep a record of the blueprint domain, calculation steps, source and any assumption that the item supplied.

If a question contains a numeric standard, verify the substance, work setting, unit and averaging period. If it asks for a first response, check whether there is immediate danger. If it asks for long-term prevention, compare the hierarchy of controls. If it asks for sample design, identify whether the decision is about a person, area, material or task peak.

Questions should have one best answer. If multiple options are defensible because a key fact is missing, note the ambiguity and revise the case. This is a useful habit for candidates and trainers because workplace decisions often require clarifying the question before recommending an action.

Build original questions from the blueprint

A candidate can create practice from a domain by pairing one task verb with a realistic setting. For “interpret,” provide a result and ask what it means. For “assess,” provide a hazard and ask which additional facts affect the risk. For “develop,” ask which training or emergency content matches the audience. Keep the answer explanations linked to a current primary source.

Vary conditions to test transfer. A time-weighted average case can change durations; a sampling case can change worker movement; a noise case can change industry; a control case can introduce an immediate hazard. If the answer stays the same only because the candidate memorized a phrase, the new facts may reveal that.

These samples are original teaching examples derived from public blueprint topics. They are not official BCSP items and should not be presented as recalled exam questions. The exam owner controls the actual test and score.

Question 9: evaluate training effectiveness

Example question

During an incident investigation, what should the technician do first after the area is safe?

  1. A. Preserve relevant evidence and gather factual information
  2. B. Select a worker to blame
  3. C. Delete incomplete records
  4. D. Announce a final root cause before interviews
Answer: A. After immediate safety is addressed, preserve evidence and gather facts. Conclusions should follow investigation, not precede it.

Record the scene, equipment condition, task steps, procedure, environment and witness observations as appropriate. Distinguish first-hand facts from assumptions and protect confidential material. Interview workers using open questions, then examine system conditions and contributing factors. The purpose is prevention and program improvement, not a premature blame assignment.

Question 10: respond to a near miss

Example question

Which approach best evaluates whether a safety training worked?

  1. A. Count attendance only
  2. B. Check whether learners can demonstrate the target skill under relevant conditions
  3. C. Ask whether the slide deck was attractive
  4. D. Count how many emails were sent
Answer: B. Training effectiveness should be evaluated against learning or behavior objectives. Attendance alone does not show that a worker can perform safely.

Match evaluation to the training goal. A knowledge briefing may use questions; a hands-on equipment task may require observed demonstration. Review trainer quality, audience fit and workplace barriers. If the worker cannot perform the task, adjust instruction or controls rather than treating attendance as success.

Question 11: communicate an evacuation

Example question

A worker reports a near miss but no injury. What is the best program response?

  1. A. Ignore it because no one was hurt
  2. B. Capture facts, assess the hazard and correct contributing conditions
  3. C. Penalize the reporter
  4. D. Use it as proof the program is fully effective
Answer: B. A near miss can reveal a hazard before injury occurs. Investigate relevant conditions and follow corrective actions.

Encourage reporting and avoid discouraging participation. Determine what happened, who could be exposed, whether controls failed and what action is needed. Track the correction and verify it. A rising report count may reflect better participation; interpret trends with other evidence.

Question 9: evaluate training effectiveness

Example question

Which communication channel is most appropriate for an immediate evacuation instruction?

  1. A. A message in next month newsletter
  2. B. An alarm and established emergency communication system that reaches affected workers
  3. C. A training record filed in HR
  4. D. An optional poster in a breakroom
Answer: B. Urgent instructions need a prompt channel that reaches people in the affected area and matches the emergency plan.

The channel must be audible or otherwise accessible under the conditions, understood by workers and coordinated with the response plan. Test it during drills and address noise, language and access barriers. A poster or later notice can support learning but cannot replace immediate warning.

Use answer explanations to connect domains

A question about a chemical spill may combine hazard communication, emergency response, PPE, sampling and ethics. The best answer may require evacuation and response-team activation before an OHST attempts measurement. Another case may ask how to communicate an exposure result without revealing confidential medical information. Identify the domains, then answer the specific task in the stem.

When reviewing a question, locate the source for any regulatory number. Check if the source applies to the industry and task. If the stem does not name a substance but assumes a limit, the question may be defective. Learning to challenge under-specified prompts is valuable; do not memorize an unsupported answer.

Use only original practice cases. Do not ask peers to share recalled live questions or reproduce proprietary question banks. Public blueprint topics and official teaching sources are enough to construct useful scenarios.

Common questions

Are these official OHST questions?

No. They are original teaching scenarios based on public blueprint topics.

Can I compare every sample to an OSHA limit?

Only when the correct substance, standard, unit and averaging period match.

Why show the calculation steps?

They make the units, weighting and assumptions checkable.