Sitonce
Country: US
Show exams for United States Hong Kong
Sign in

CSP Exam Sample Questions and Answers

Updated 7 min read
Key takeaway

These original CSP-style questions test control selection, incident-rate arithmetic, PSM change review and exposure-limit interpretation.

  • They are practice examples, not official BCSP items.
  • Read each stem for the requested decision, solve from the facts given, and use the rationales to understand why alternatives are weaker.
On this page7 sections
  1. How to use these questions
  2. Question 1: choose a source control
  3. Question 2: distinguish rate numerators
  4. Question 3: manage process changes
  5. Question 4: match the sample to the limit
  6. Review the reasoning pattern
  7. A short self-review
Question source
Original practice examples written for this guide
Current outline
CSP11 V.2024.04.24
Official item status
Not BCSP questions; no claim of live exam exposure
Best use
Attempt first, then review the reasoning and distractors

How to use these questions

Try each item before reading the rationale. Write down the decision the stem asks for, the relevant facts, and any calculation. Then compare your reasoning with the explanation. The point is to learn why an answer fits the scenario, not to memorize a letter or assume that one example predicts the full examination.

These are original instructional questions, not official BCSP content. They are not copied from a protected test or presented as recalled live items. Check the current blueprint and applicable technical source when a question concerns a rule. Practice items teach a concept; the credential owner’s current materials define the exam.

Example question

A packaging line repeatedly exposes workers to airborne dust when bags are emptied into an open hopper. Which option is the strongest durable control to investigate first?

  1. Require workers to wear respirators and repeat annual training.
  2. Enclose the transfer and capture dust at the source, after evaluating process feasibility.
  3. Rotate workers so each person spends less time at the hopper.
  4. Post a warning sign near the line.
Answer: B. The enclosed transfer and source capture use engineering design to reduce release and exposure. Feasibility and new hazards still need review. Respirators, rotation and signs may supplement a control plan, but they leave the open source in place and rely more on worker behavior.

Question 1: choose a source control

The strongest answer is the enclosed transfer and capture system. It addresses the emission point and reduces reliance on repeated protective action. The stem says exposure occurs during an open pour, so a control designed around the source is relevant. An actual design must consider capture velocity, material properties, cleaning, maintenance and any hazards introduced by enclosure.

Respirators may be appropriate as an interim or supplementary measure, but selecting them requires a respiratory-protection program and task-specific evaluation. Rotation reduces individual exposure time but can transfer risk to more workers and does not eliminate the source. A sign communicates a hazard but does not control dust.

Example question

A site records 7 total recordable cases, including 2 DART cases, over 350,000 hours worked. What are the total recordable case rate and DART rate, respectively?

  1. 4.00 and 1.14
  2. 1.14 and 4.00
  3. 2.00 and 0.57
  4. 7.00 and 2.00
Answer: A. Total recordable rate = 7 × 200,000 ÷ 350,000 = 4.00. DART rate = 2 × 200,000 ÷ 350,000 = 1.142857, or about 1.14. The numerator differs by measure; both use the same matching hours.

Question 2: distinguish rate numerators

The answer is 4.00 for total recordables and 1.14 for DART. Calculate each separately because the numerator is different. The rate formula normalizes the case count by hours worked: cases × 200,000 ÷ hours. The 200,000 constant represents 100 full-time workers at 40 hours per week for 50 weeks.

Option B reverses the measures, likely from switching the numerators. Option C omits part of the normalization. Option D reports raw counts rather than rates. Keep the labels beside the numbers so a correct calculation is not assigned to the wrong metric.

Example question

A covered process will replace a pump with a higher-capacity model. What should the team do before operating the changed process?

  1. Start the pump and update the operating procedure after observing performance.
  2. Complete the applicable management-of-change review, address affected information and procedures, train affected personnel, and verify readiness before startup.
  3. Treat the pump as a maintenance replacement and skip review because the equipment type is unchanged.
  4. Rely on the vendor’s installation certificate as the process hazard review.
Answer: B. A capacity change can affect process conditions, hazards, safeguards and procedures. For a covered process, evaluate the change under the applicable MOC and readiness requirements before startup. The exact documents and reviews depend on the standard and change scope; a vendor certificate does not replace the employer’s process review.

Question 3: manage process changes

The best answer is the pre-startup MOC and readiness sequence. Higher capacity can alter flow, pressure, relief demand or control response even if the pump looks similar. Review the technical basis and safety impact, update affected process safety information and procedures, determine training needs and verify startup readiness under the applicable PSM requirements.

Option A puts operation before hazard review. Option C assumes that an equipment replacement cannot change process risk. Option D confuses a vendor installation record with the employer’s obligation to evaluate process effects. Applicability must be confirmed under 29 CFR 1910.119.

Example question

A fictional contaminant has an illustrative 8-hour TWA of 10 mg/m³ and a separate 15-minute STEL of 20 mg/m³. A full-shift sample is 8 mg/m³, while a representative 15-minute task sample is 23 mg/m³. What is the sound interpretation?

  1. Both limits are met because the full-shift result is below 10 mg/m³.
  2. The TWA comparison is below its illustrative value, but the short-term result exceeds the illustrative STEL and requires follow-up.
  3. The STEL should be averaged across the full shift.
  4. The result proves a legal violation for every real chemical with similar units.
Answer: B. The averaging periods differ. An 8-hour average below the illustrative TWA does not cancel a 15-minute sample above a separate illustrative STEL. In real work, verify the chemical-specific current limit, method, units, sampling representativeness and legal applicability; these numbers are fictional.

Question 4: match the sample to the limit

The correct interpretation is that the full-shift result is below the stated illustrative TWA, while the 15-minute sample is above the illustrative STEL. The two values answer different exposure questions. A shift average can hide a high short-duration task exposure.

The values in the stem are fictional and do not represent a real substance or legal limit. In practice, identify whether the value is an OSHA PEL, NIOSH REL, ACGIH TLV or another benchmark. Confirm the substance, jurisdiction, averaging period, sampling method and any skin notation or mixture rule before concluding that a legal violation occurred.

Review the reasoning pattern

Across the four items, the task changes: select a control, calculate rates, manage a covered process change and interpret exposure measurements. A strong test-taker notices that the correct method changes with the question. The hierarchy applies to the dust scenario, the 200,000 constant to injury rates, PSM to a covered process, and averaging-period logic to exposure limits.

The distractors are plausible because they resemble real safety actions. Training and signs have a role; raw case counts are real data; vendor installation documents can be useful; full-shift samples matter. Their weakness is that they do not answer the exact question. Read the requested outcome before choosing an option.

For each calculation, write units and labels. For each legal question, establish applicability. For each control question, compare reliability and source reduction. For each measurement, match the sample and limit period. These habits transfer to new items better than memorizing these specific scenarios.

A short self-review

  • Could you explain why each distractor is weaker?
  • Did you distinguish total recordables from DART?
  • Did you treat the exposure values as fictional scenario facts?
  • Did you identify the applicability condition for PSM?
  • Did you choose a durable control without assuming engineering is automatically feasible?

Use the questions as a small diagnostic, not a readiness guarantee. If you missed an item, return to the relevant concept and solve a different example after a delay. The current official CSP11 blueprint and primary standards should guide broader study. No commercial or original practice set can establish an official passing score.

Common questions

Are these official CSP exam questions?

No. They are original instructional examples and are not represented as BCSP questions or recalled live exam items.

How should I review a missed sample question?

Identify the decision requested, classify the error, review the concept and solve a new scenario after a delay. Do not memorize only the answer letter.

Can a practice score predict my CSP result?

A practice score measures performance on that set only. It does not establish BCSP’s official passing cutoff or a guaranteed result.